Shop Press

Shop Press is the news and idea hub for everything related to working on cars and trucks, focusing on repair, technology, and wrenching lifestyle.

From the creative minds at:

FEATURE STORY

How Often Should You Really Flush Coolant? (VIDEO)

How Often Should You Really Flush Coolant? (VIDEO)

How do you know when it’s time to flush coolant? Technicians may have different views on the subject, but Dorman Training Center instructor Pete Meier explains how using a test strip at every service is a surefire way to get an accurate picture of the coolant’s health.

read more

Hot Off the Press

How Often Should You Really Flush Coolant? (VIDEO)

Description How do you know when it’s time to flush coolant? Technicians may have different views on the subject, but Dorman Training Center instructor Pete Meier explains how using a test strip at every service is a surefire way to get an accurate picture of the...

Colin Chapman: The Philosopher of Motion (Part 1)

Car designers have a lot of brain synapses firing. Some designers are driven by the pursuit of beauty, while others are motivated by the pursuit of speed. Giorgetto Giugiaro, Marcello Gandini, and Battista Pininfarina, though responsible for cars that raced, were...

Maximum Voltage Reading – ASE Practice Question (VIDEO)

Description Technician A is using the min/max function of a digital voltmeter to test the battery and charging system on a customer’s vehicle. He notes a max reading of 17.2 volts has been recorded. Technician B says that the alternator has failed and is overcharging....

The Story of Dagmar Bumpers

If you’ve read my work here on Shop Press, you know I’m a sucker for chrome and mid-century automotive design. This week, I'd like to take a look at one of my favorite examples of that era: "Dagmar bumpers," the colorfully common slang used to describe the...

Should You Charge More When Dealing with Tire Sealant? (VIDEO)

Description Aerosolized tire sealant is widely available, and in some vehicles, it is used in place of a full-size spare. While this “tire repair in a can” might be the best solution in a jam, it creates a messy, stinky situation for a tech changing the tire for a...

An Ode to “Car Talk”

Back in the early aughts, I lived in the Washington, D.C. area for about nine years. Since my parents live in Pennsylvania, this necessitated many three-and-a-half-hour drives (as little as three, if I was lucky) back home for holidays or just a regular visit. At the...

Testing Battery State of Charge – ASE Practice Question (VIDEO)

Description Technician A and Technician B are discussing battery testing. Technician A says that an open circuit voltage of less than 10.5 volts indicates a bad battery. Technician B says that a reading of 12.5 volts indicates an 80% state of charge. Who is correct?A)...

PSA: Be Safe With Carburetor Cleaner, Too

Recently, I wrote about how brake cleaner can be hazardous if not used correctly, and how you should take safety precautions when using it. One of our readers had an insightful comment on the piece.Now, I think it’s debatable that carburetor cleaner is more hazardous...

PSA: Take a quick look at your punches and chisels (and be sure they’re ready for service)

by | Mar 28, 2023

Rebuilding ratchets, cleaning the welder tips and nozzles, and oiling air tools all fall under the umbrella of things we know we should do, but don’t until a job stops. Dressing chisels and punches, however, is a housekeeping task I’ve found not everyone knows they should be doing. In the spirit of safety: dress your punches and chisels!

Chisels and punches need maintenance. Your safety may depend on it.

Chisels and punches need maintenance. The business end of your chisels and taper punches can deform under use as you likely know. (You’re not beating the tar out of your pin punches, I would hope.) Chisels occasionally need their edges restored, and punches sometimes need to be cleaned up as well. I personally prefer a nice round, flat striking face on my punches, just like my tools had when they were new. Same goes for the chisels: a nice cutting edge simply makes them work better.

However, it’s the other end that gets dangerous. The end you beat on, I mean. The harder you hit it, the more it peens over—they “mushroom.” Those mushroomed sections, though, turn into a giant liability, because occasionally they break free. I’ve busted them myself when I was younger and dumber. Now I know better. I dress my tools—both ends.

chisel and pushes on work bench

Photo by: Justin Mondschein.

Most of my friends and colleagues take this job on with a bench grinder. Most also keep a little cup of water handy so as to not ruin the temper of the tool. A flap disc or belt sander works well, too. I’ve used a file more than once; even that only takes a few swipes if you keep up with the work. I do the business end, then put a little taper on the striking end, and then back in the box they go, ready for work when I need them.

No matter how you do it, take a peek at your striking tools and make sure peepers and paint aren’t gonna get damaged. Don’t forget your splitting wedges at home if you burn wood—those are usually the worst offenders.

Photos by: Justin Mondschein.

The articles and other content contained on this site may contain links to third party websites. By clicking them, you consent to Dorman’s Website Use Agreement.

Related Articles

Shop Press Comment Policy

Participation in this forum is subject to Dorman’s Website Terms & Conditions. Please read our Comment Policy before commenting.

Subscribe
Notify of
guest
1 Comment
Newest
Oldest Most Voted
Inline feedback
View all comments